Related topics

hp-ux 10.20 on C240
The install will hang randomly anywhere from the first floppy to the end of the initial setup, the blue screen with the animated slashes. The only recourse at that point is a cold boot. The hardware is a Tyan Titan III with a P5/133, 64Mb, Adaptec1542 (isa) with Micropolis HDD, Wangtek tape drive and Texcel CD-ROM.

problems installing win98 as guest on virtual disk
I believe that the initial setup of a system is quite fun. My boot sector loads in a minimal kernel, which contains an IDT and GDT at the beginning of it. The system seems to hang when I call either LIDT or LGDT. My IDT is currently empty (full of 0's) but I've called CLI, so that shouldn't matter, should it?

SBS2000 Upgrade: Driver corrupted exec. memory pool
-My system is slow or hangs when sizing memory -My system doesn't recognize files starting with #! -Where do I get POP binaries? -What is Everest? ..... Second, if you use this to do the initial setup of the modem, DOCUMENT YOUR SETTINGS somewhere so that if your modem does die, you'll have the settings you used

upgrade/install problems
Hmmm, the next port of call would be to boot into Safe Mode, run MSCONFIG and disable anything that is not Microsoft / part of Windows, then boot back into The initial setup session went fine, but now it just comes up to a dark blue screen and just hangs. (This is the screen where the hardware is supposed to be

Boot Problems
mark mea...@home.com 24hoursupport helpdesk during the process of trying to det up multiple boot system (95, NT, 98) I repartitioned & reformattted (FAT) my hard disk (maxtor 27 gig) and installed 95. It completes the initial setup but when the computer restarts it hangs after it says verifying DMI Pool data.

installation hangs after copying files
B...@earthling.net comp periphs scsi On Sat, 03 Apr 1999 04:11:30 GMT, e...@saturn.rings.com wrote: I'm having no luck getting NT4 to boot in a partition The initial setup went ok. Rebooted and made selections. When the install read from the CDRom, it would hang at anywhere from 10 to 90 percent of files read.

boot problem with Win98SE / system registry
The Scary thing is I have already tried installing a new XP to a different partition and after the initial setup phase, when the system reboots, I still hang after POST. In the recovery console I can see and read the new boot.ini, but I am sure that I am not getting to the point where you would normally see a boot

cannot get Windows to Boot from my hard drive
e...@saturn.rings.com comp periphs scsi I'm having no luck getting NT4 to boot in a partition above 8G. NT4 will do the first part of the install, The initial setup went ok. Rebooted and made selections. When the install read from the CDRom, it would hang at anywhere from 10 to 90 percent of files read.

install problems
These installation procedures will ensure a pure Windows 2000 system that does not support multiple boot options. Note: Installation of all the components .... 7.6 Configure Certificate Services The Add/Remove Programs dialog should contain the Certificate Services option, if requested during the initial setup.

Racal Interlan ES3210 Boot Hangs with "G2"
Perhaps he is extrapolating from the initial setup. Once the machines were up and configured they worked very reliably. The machines are still in heavy use and My choice of operating system was not stopping systems to the point that they wouldn't boot the ARC console. Other shutdowns were also diagnosed by our

cisco 2501 Config (Newbie)
Problem: I ran the initial setup, and configured my router with the ip's assigened by ISP...but the problem is that i am getting a "Line Protocol is down .... output hang never Last clearing of "show interface" counters never Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec,

Hard Drive performance with the 7DXR terrible
DCDIAG followed by NETDIAG: C:\Program Files\Support Tools>dcdiag Domain Controller Diagnosis Performing initial setup: Done gathering initial info. Doing initial required tests Testing server: Admin-HS-Grade9\ADMINROOTDC03 Starting test: Connectivity ......................... ADMINROOTDC03 passed test Connectivity

TUSL2-C Can't boot anymore
NTFS/FAT are the same when it comes to loading this stuff....stick the CDrom in the tray before you turn on the machine, boot from a cdrom, hit f6, .... On page 3-23 I create may partitons during the initial setup so that my cd rom shows up as F: or G: always. It gets bumped to F: or whatever by the fact that the

SA6R W2K Install problem
Billy m...@women.com microsoft public win2000 setup You should have under %systemroot%\repair the hives created during initial setup. If you did backup registry (didn't you? :), you should have more recent hives under repair\regback. Replace hives in system32\config one by one, and maybe you'll find it's not

Total hang on boot, now on setup
Without the ACE patches, the C240 will not boot. Krys Caputa wrote: I've installed a July 1997 version of 10.20 on a C240 successfully. Where does it hang, during the installation or after during the reboot? It hangs during the initial setup of install, right after the messages below. Never gets to installation

FYI. W2K with Promise Ultra/66 and TNT 16Mb on VA-503+
I do have 2 gigs of RAM, but at the point in the 98 install when the initial setup done from boot floppy is complete and it is ready to reboot from the hard drive, Still after 3 attempts to install 98SE the pc hangs during the OS loading. Then I wondered if the Hyper Threading could be a problem for 98 and have

CDrom hang with 32-bit OS
Michael Stevens Mstev...@notmvps.org microsoft public windowsxp general Manny wrote: It only allows the initial setup in the dos screens. When setup has the system On reboot after the copying of setup files, does the system stop at the "press a key to boot CD" and hang at that point? If a key is not pressed,

Windows XP Installation Problem (black Screen)
(In PCI slot 3) During the initial setup phase (Where NTsetup loads various device drivers), the setup program hangs & later bluescreens after loading CDROM file system drivers. Also, NTsetup only detects one CPU, even though it uses the multiprocessor kernel. The bluescreen gives the message "Inaccessible boot

P2B-S & Plextor PX32TSi
After going through the initial setup, Windows 2000 setup asks me to produce a file called NT5INF.CAT. I found it in the \i386 folder, but it's NT5INF.CA_. How do I fix this problem because I would really like to get it up and running and it just hangs at that spot every time. By the way, I have a dual boot system

mouse hangs up install
After the initial setup was done and the computer rebooted it hung at the startup screen. The little blue scrolling indicator at the bottom of the screen If the Setup hangs again, turn the PC off instead of to reboot. This will cause Setup to detect that there was a problem and it will try to workaround on it's